10/26/2022 0 Comments Spindle nut socketVW 36mm Rear Axle Nut, Beetle, Super, Ghia, Thing, Type 3 – All, Type 2 1955-63. What size is the axle nut on a VW Beetle? Reuse of the old nut could potentially cause the nut to loosen during vehicle operation. In these applications, a new nut must always be used when installing a hub. This is typically when a one-time-use, self-staking nut secures the hub. Should you replace hub nut?īe aware that some hubs come with a new nut in the box. No, you actually should not drive without the axle nuts, for if you do, the trailing arms and the stub axles could get damaged as a result of that. The tab or tang washer is designed for a single use. The tab or tang style spindle washer is used to lock the spindle nut into place by bending one of the tabs into the groove of the nut. Nut width and height vary with the size of the castle nut. Size is specified in inches, usually fractional rather than decimal. Typically, sizes range from about 1/4″ to 1 1/2″. What size is the spindle nut on a Dexter Axle?Ĭastle nut size refers to its nominal thread diameter. If you count 9 lines, the size is a 9-mm (millimeter) nut. If the nut is metric, count the number of lines on the tape measure to find the measurement. Stretch the tape measure across the nut’s diameter to the flat-side directly across from the one your pulling from. What size is the axle nut on a 2009 Dodge Journey?Īxle Nut Hex Size (mm) : 32. What size is the axle nut on a Chevy 1500? SPINDLE NUT SOCKET FREEThe final step is to use a dial indicator to verify the end play or free movement of the tire and wheel assembly along the spindle axis. See chart for exact torque specification. Nuts 2-5/8″ and over should be torqued to 250-400 lbf-ft. Generally, jam nuts less than 2-5/8″ should be torqued to 200-300 lbf-ft You should’ve torqued those nuts down quite a bit. Over tightening won’t put more of a strain on the bearings in this sort of design. How important to replace axle nut with a new one every time you remove it? Official Ford service procedure states that if you have to remove an axle nut, you should discard it and replace it with a brand-new one. What happens if you over tighten a spindle nut?Īn axle nut that is too tight will put too much preload on the hub bearings thus diminishing their life expectancy. The hub nut is a crucial part of what gives you drive in your car. SPINDLE NUT SOCKET REGISTRATIONIf you need to replace the hexagonal nuts on your car, simply enter your registration details here and find your perfect fit. Hub nuts are responsible for keeping the driveshaft within the wheel hub on front-wheel or 4×4 vehicles. It is a 1/2″ drive, 30mm, 12 point socket. The axle is a rotating shaft that helps secure the wheels to the rest of the vehicle and facilitate movement, and the axle nuts will be secured to lugs that are attached to either end of the axle. What is axle nut?Īxle nuts are pieces of hardware that are used to help secure a wheel to an axle. This is 1″ – 14 thread standard castle nut that will work on nearly all trailer axles. This 3/4” spindle nut is commonly used on idler and braking hubs. What size is trailer hub nut?ģ/4″ Spindle nut for trailer spindles. What size are axle bolts?ġ4mm bolts are sold in pairs. However, if the stub of cv shaft sticking out is all rusted up/threads corroded, then you will likely damage the threads on the nut when you remove it. IF the nut comes OFF clean, then yeah, you can probably reuse it. Some axle nut socket designs resemble a common socket wrench. These types of vehicles commonly use a splined axle to be tightened into the wheel hub by the axle nut, requiring a specially-designed axle nut socket to remove the nut. Do you need a special socket for axle nut? You will use a 1-1/2 inch socket on this castle nut or we usually use a channel lock for these installations.
0 Comments
Leave a Reply. |
AuthorWrite something about yourself. No need to be fancy, just an overview. ArchivesCategories |